Garbage Disposal Humming but Not Spinning — What to Do
General information only — not a substitute for a qualified service person's judgment about your disposal. This page follows InSinkErator's own published repair steps, in the maker's order.
This page never opens the unit. Every step below is done from outside the disposal — a wrench in the socket on the bottom, a button on the bottom, and tongs from above. If the fix needs more than that, it is service work, and the page says so and stops.
First, the safety setup
Make certain the disposal's switch is in the off position before you touch anything. InSinkErator's instruction sheet also says to turn off the water. If the sink is full of water, wait for it to drain, or bail the water out with a bucket or pot. And the rule that outranks all the others: never put your hand in the disposal — not to feel for the jam, not to grab the object, not ever. The plate can move without warning, and "off" is not a promise your fingers can rely on.
The fix, in the maker's order
- Find the wrench. Every InSinkErator is shipped with a self-service wrench. It is silver colored, shaped like a little crank, and about four inches long. If you cannot find it, a standard 1/4-inch Allen wrench does the same job.
- Crank the plate free from below. The hole for the wrench is under the sink, at the bottom of the disposal, dead center, facing the floor. Put the wrench in and use it like a crank, working it back and forth. If the wrench will not turn easily, it is OK to use some force — the wrench is designed to bend before any damage is done to the disposal. Keep working until the wrench turns freely in complete circles in both directions. (The maker's instruction sheet puts the goal this way: work the wrench back and forth until it completes one full revolution, then take the wrench out.)
- Look inside with a flashlight — and use tongs. Shine the light down into the disposal. Pay special attention to the area around the outer edge of the shredding disk, where the little teeth are — that is where jammed objects lodge. If you see anything in there, remove it with tongs or pliers. Not your fingers.
- Press the red reset button. The overload protector sits on the bottom of the disposal, facing the floor. It is a small square red button. If it has tripped, you will see the button dropped down about a quarter of an inch (5 mm). Gently press it. If it does not stay up, wait ten minutes and try again — the motor needs to cool. The maker's instruction sheet gives the same cooling idea in shorter form: let the motor cool for 3 to 5 minutes, then lightly push the reset button.
- Run cold water, then switch on. Turn on a cold stream of water and turn the disposal switch on. It should now run. If it jams again, use the wrench again — InSinkErator says plainly that you may need to repeat the process several times.
If it stopped and won't make any sound at all
A disposal that will not run — no hum, nothing — may have shut itself down. InSinkErator explains that if the disposal is clogged, if it is run for a very long period of time, if it overheats, or if there is something wrong with it, it shuts down automatically and needs to be reset. The reset is the same red button: switch off, gently press the red button in, wait ten minutes and try again if it will not stay in, then cold water and switch on. The instruction sheet adds one more check: if the motor remains inoperative after the reset, check the service panel for tripped circuit breakers or blown fuses.
Stop lines.
Hands stay out — always. This bears repeating because it is the whole ballgame with this appliance: InSinkErator says do not place your hand in the garbage disposal at any time. Tongs and pliers reach everything this fix needs to reach.
Nothing here opens the disposal. No covers come off, no wires get touched, no pipes get disconnected on this page. Advice elsewhere that has you prying at the plate from above with a stick, taking the unit apart, or handling its wiring is outside the maker's published fix, and this page does not use it.
If the reset button will not stay in, or you have to keep resetting it, the disposal needs service or replacement — that is InSinkErator's own line. And if the disposal continues to jam after the wrench treatment, it may need service.
Keeping it from jamming again
InSinkErator's own tips for success: run the disposal along with a moderate flow of cold water, and keep the cold water running for a few seconds after grinding is complete. Avoid hot water when grinding food waste — it is fine to drain hot water into the disposal between grinding periods. And never pour grease or fat into the disposal or the drain.
One honest note about cost
If the disposal keeps jamming and needs service, InSinkErator says this: if the problem is due to a quality issue, the company may pay to have an authorized service center service the disposal in your home at no charge to you. That is the maker's word for defects — it is not a promise about every jam, and this page does not stretch it into one.
General information only — not a substitute for a qualified service person's judgment about your disposal. If the unit smokes, sparks, leaks, or trips its reset again and again, stop and call for service. The maker's own repair text below is the whole basis of this page, and it is worth reading in the original.
Sources
InSinkErator, published repair tips for a jammed or stopped disposal (insinkerator.com support materials): every InSinkErator is shipped with a self-service wrench, silver colored, shaped like a little crank, about four inches long; a standard 1/4-inch Allen wrench can be used instead; make certain the disposal's switch is in the off position; do not place your hand in the garbage disposal at any time; if the sink is full of water, wait for it to drain or bail it out with a bucket or pot; the wrench hole is at the bottom of the disposal, dead center, facing the floor; use the wrench like a crank, and it is OK to use some force because the wrench is designed to bend before any damage is done to the disposal; work until it turns freely in complete circles in both directions; the overload protector is a small square red button on the bottom of the disposal, dropped about a quarter of an inch (5 mm) when tripped; gently press it, and if it does not stay up, wait ten minutes and try again; look inside with a flashlight, paying special attention to the outer edge of the shredding disk where the little teeth are, and remove objects with tongs or pliers; the disposal may need the process repeated several times; if it continues to jam, it may need service, and if the problem is due to a quality issue InSinkErator may pay for an authorized service center to service it in the home at no charge; a disposal that is clogged, run for a very long period, overheated, or faulty shuts down automatically and needs the red-button reset; if the reset button still will not stay in, or the overload protector has to be reset repeatedly, the disposal may require service or replacement; run the disposal with a moderate flow of cold water and keep cold water running a few seconds after grinding; avoid hot water when grinding; never pour grease or fat into the disposal or drain. Read in full November 7, 2026.
InSinkErator instruction sheet, "Releasing Disposer Jam" (the maker's printed instructions for the unit): turn off the disposer and the water; insert one end of the self-service Jam-Buster Wrench into the center hole on the bottom of the disposer and work it back and forth until it completes one full revolution; remove the wrench; use tongs to reach into the disposer and remove any objects; allow the motor to cool for 3 to 5 minutes, then lightly push the red reset button on the bottom of the disposer; if the motor remains inoperative, check the service panel for tripped circuit breakers or blown fuses. Read in full November 7, 2026.
Checked November 7, 2026.
Related guides: Garbage Disposal Leaking, Dishwasher Not Draining, Oven Not Heating, Refrigerator Not Cooling and Dryer Not Heating.