Garbage Disposal Leaking in Plain Words
General information only — not a substitute for your disposal's own manual or a qualified plumber's judgment about your disposal. This page follows the leak guidance InSinkErator and Moen publish on their own support sites. InSinkErator opens every one of its leak pages with the same instruction: before attempting a repair, read and understand the entire InSinkErator safety and installation instructions. Work with the power to the disposal off, and keep hands and fingers out of the grind chamber — the checks here are all outside the unit: screws, rings, clamps, gaskets, and watching where water appears.
Step one: catch the leak in the act
Each maker publishes its own find-the-source test. They are the same idea with different paper:
- InSinkErator's newspaper test. Empty the area below the sink. Spread a sheet of newspaper flat over the bottom of the cabinet below the sink and secure it with tape — dripping water leaves a wet spot on the paper that shows you where it fell from. Then work through three stages, looking for leaks at each one: place stoppers in the sink(s) and fill them with water, and leave them full for a while; remove the stoppers and let the sink drain; then turn on the water and the garbage disposal and let them run while you look. If leaks are not found, keep the paper in place for a few days.
- Moen's paper-towel test. Place a sink stopper in the sink and fill the sink with water. Wrap paper towels in three places: directly at the very top of the garbage disposal around the sink flange; around the drain discharge elbow on the side where it connects to the disposal; and around the dishwasher connector on the side where it connects to the dishwasher. Release the stopper and let the water drain, then check all the paper towels: if one is wet, the leak is coming from that area, and it is caused by an issue with the installation of that specific item.
Both makers also give the same fallback if no leak shows itself: the water may be from somewhere else entirely. InSinkErator's list of other suspects: water filters, the dish sprayer, the faucet, the dishwasher drain hose, the sink/countertop seam, and countertop joints.
Leaking at the top: the mounting assembly
InSinkErator's mounting-assembly page gives four checks, in its order:
- Check for proper assembly — that the mounting assembly is properly assembled.
- Check the locking ring — ensure that the garbage disposal locking ring is rotated fully to the right.
- Check for loose screws — check the three screws, making sure each is tight and secure.
- If this is a new installation — check under the sink flange for excessive plumber's putty; InSinkErator's fix is to remove the garbage disposal, remove any excess putty, tighten the screws, remount the disposal, and test for leaks again.
Moen's top-leak page for an existing disposal names the causes behind the same wet spot: the sink flange deteriorating, the rubber or fiber gasket or the cushion mount damaged or deteriorated (inspect the mounting hardware, gasket, and cushion mount, and replace if necessary), the mounting assembly screws having loosened (verify they have not), and worn sealant (if the sealant is worn down it will not seal properly and needs to be replaced with new sealant). The two makers are describing the same joint from two sides: tight and fully locked (InSinkErator) around parts that are still sound (Moen).
Leaking at the side: discharge and dishwasher inlet
The discharge is where ground-up waste leaves the unit for the drain trap. InSinkErator's discharge page:
- Check the discharge — that the discharge nut or bolts are tight.
- Check the gasket — for accumulated debris, cracks, or rips; replace any cracked parts.
- Check the discharge elbow — look for cracks on the elbow and verify that the elbow/trap joint is tight; replace any cracked parts.
- Evolution units — confirm the discharge tube is inserted into the Anti-Vibration Tailpipe Mount correctly and secured with the original spring-load hose clamp; check the mount for cracks or damage; and if water is coming directly from the discharge opening, check whether the detergent shield is buckled.
The dishwasher inlet is where a dishwasher's drain hose connects, if yours does. InSinkErator's inlet page (it applies only if a dishwasher drain hose is attached): check whether the knockout plug was removed — the small plug inside the disposal at the dishwasher inlet has to come out for the dishwasher drain hose to hook up; check that the clamps are tight; check that the hose adapter, if used, is intact and tight; and verify that the elbow/trap joint is tight.
Leaking at the bottom: the makers' answer changes
InSinkErator's published leak guidance handles the bottom as a confirm-first case, in this order: if water appears to be leaking from the bottom, confirm it is not leaking from somewhere else — such as the mounting assembly — and dripping down to the bottom. The same confirmation applies to a leak that seems to come through the wall of the container body: confirm it is not leaking from the top and dripping down through the wall. Only if confirmed is the bottom leak real, and then InSinkErator's words are that your garbage disposal may need service; a leak at the motor joint, it says, may need to be replaced or require an authorized service center to diagnose the problem. Its commercial troubleshooting says the same thing in shorter form: a leak from the bottom of the unit indicates an interior seal is damaged — first make sure the disposer is not leaking from anywhere else within the unit, and if it is only leaking from the bottom, call an authorized service agent.
What is not in the makers' guidance: any homeowner procedure for the inside of the unit. The forum answers that talk a disposal owner through removing the flywheel to replace the seal under it, or sealing a housing with epoxy, have no counterpart on InSinkErator's or Moen's pages — the makers treat a confirmed bottom, body, or motor-joint leak as service or replacement, and this page follows them.
If the leak is in the plumbing next to the disposal
One more outcome in InSinkErator's guidance: if the leak is from adjacent plumbing rather than the disposal itself, tighten the joints as needed. That is the discharge elbow/trap connection and the trap beyond it — ordinary plumbing joints, not the disposal. If the leak pattern doesn't match any section here, or the water is reaching the disposal's electrical connection, stop and call a plumber; InSinkErator's guidance ends with the same offer for stuck cases — help finding a certified plumber.
The bottom line: Dry the cabinet, lay down newspaper (InSinkErator) or wrap the three joints in paper towels (Moen), and let a fill, a drain, and a run tell you where the water starts. Top leaks are the mounting assembly — locking ring fully right, three screws tight, gasket, cushion mount, and sealant sound. Side leaks are the discharge (bolts, gasket, elbow) or the dishwasher inlet (clamps, adapter, plug). A leak that truly starts at the bottom is an internal seal, and the makers' answer is service or replacement — not a seal kit.
General information only — not a substitute for your disposal's own manual or a qualified plumber's judgment about your disposal.
Sources
InSinkErator, "Garbage Disposal Leaking from the Mounting Assembly" (insinkerator.com): if the mounting assembly is leaking, check to see if it is properly installed (materials needed: screwdriver) — check that the mounting assembly is properly assembled; ensure that the garbage disposal locking ring is rotated fully to the right; check the three screws, making sure each is tight and secure; and if this is a new installation, check under the sink flange for excessive plumber's putty — remove the garbage disposal, remove any excess plumber's putty, tighten the screws, remount the garbage disposal, and test for leaks again; tips for success: empty the area below the sink, spread a sheet of newspaper flat over the bottom of the cabinet below the sink and secure with tape, and if water drips from a leaking area it will leave a wet spot on the paper — place stoppers in sink(s) and fill with water, leave sinks full for a while, look for leaks, remove stopper(s) and let sink drain, look for leaks, turn on the water and garbage disposal and allow them to run while looking for leaks; if leaks are not found, keep paper in place for a few days, and if you see no indication of leaks, water may be from other sources — check water filters, dish sprayer, faucet, dishwasher drain hose, sink/countertop seam, and countertop joints. Read in full November 8, 2026. https://www.insinkerator.com/en-us/support/garbage-disposal-leaking-from-the-mounting-assembly
InSinkErator, "Garbage Disposal Leaking at the Discharge" (insinkerator.com): before attempting to repair your garbage disposal, read and understand the entire InSinkErator safety and installation instructions; to stop the discharge from leaking — check that the discharge nut or bolts are tight; check the gasket for accumulated debris, cracks or rips, and replace any cracked parts; check the discharge elbow for cracks and verify that the elbow/trap joint is tight, and replace any cracked parts; on Evolution units, confirm the discharge tube has been inserted into the Anti-Vibration Tailpipe Mount correctly and is secured properly with the original spring load hose clamp, check the Anti-Vibration Tailpipe Mount for cracks or damage, and if water is coming directly from the discharge opening, check if the detergent shield is buckled; the same newspaper leak-locating tips and other-sources list as the mounting-assembly page. Read in full November 8, 2026. https://www.insinkerator.com/en-us/support/garbage-disposal-leaking-at-the-discharge
InSinkErator, "Garbage Disposal Leaking at the Dishwasher Inlet" (insinkerator.com): this troubleshooting guide only applies if you have a dishwasher drain hose attached to the garbage disposal dishwasher inlet; check if the knockout plug was removed — the knockout plug is a small piece inside the garbage disposal at the dishwasher inlet and needs to be removed in order to properly hook up the dishwasher drain hose; check to see if the clamps are tight; check that the hose adapter, if used, is intact and tight; verify that the elbow/trap joint is tight; the same newspaper leak-locating tips and other-sources list. Read in full November 8, 2026. https://www.insinkerator.com/en-us/support/garbage-disposal-leaking-at-the-dishwasher-inlet
InSinkErator, garbage disposal leak troubleshooting (the maker's published leak guidance, insinkerator.com support): if the top of your garbage disposal is leaking from the mounting assembly, you need correct mounting installation answers; if water appears to be leaking from the bottom, confirm it is not leaking from somewhere else (such as the mounting assembly) and dripping down to the bottom — if confirmed, your garbage disposal may need service; if it is leaking through the wall of the container body, confirm it is not leaking from the top of the garbage disposal at the mounting assembly and dripping down through the wall — if confirmed, your garbage disposal may need service; if your garbage disposal is leaking at the motor joint, it may need to be replaced or require an authorized service center to diagnose the problem; if it is leaking from adjacent plumbing, tighten joints as needed; and for help, find a certified plumber. Read in full November 8, 2026.
Moen, "Leak Around Top: Existing Garbage Disposal" (solutions.moen.com): this article deals with leaking around the top of the disposal and is specifically for existing disposals, not new installations; leak test — place a sink stopper in the sink and fill the sink with water; wrap paper towels directly at the very top of the garbage disposal around the sink flange; wrap paper towels around the drain discharge elbow on the side of the garbage disposal where it connects to the garbage disposer; wrap paper towels around the dishwasher connector on the side of the garbage disposal where it connects to the dishwasher; once you have wrapped all the necessary places, release the stopper and let the water drain; check all of the paper towels to see if they are wet — if any are wet, the leak is coming from that area and is caused by an issue with the installation of that specific item; leaking around the top of a garbage disposal is usually caused by one of the following — sink flange deterioration; the rubber or fiber gasket or cushion mount (inspect the mounting hardware, rubber or fiber gasket, and cushion mount for any damage or deterioration and replace if necessary); loose screws (verify that the mounting assembly screws have not loosened); and worn sealant (if the sealant is worn down then it won't seal properly and will need to be replaced with new sealant). Read in full November 8, 2026. https://solutions.moen.com/Article_Library/Leak_Around_Top%3A_Existing_Garbage_Disposal
Checked November 8, 2026.
Related guides: Garbage Disposal Humming but Not Spinning, Gravel Tons Calculator, How to Make Slime, Lawn Mower Won't Start and How Many Bags of Concrete for a Post Hole.