Dryer Not Heating in Plain Words
General information only — not a substitute for your dryer's own manual or a qualified appliance technician's judgment about your dryer. This page follows Whirlpool's Product Help pages for electric and gas dryers and Samsung's US support guide. The repair internet's standard next steps — opening the cabinet and testing the thermal fuse, heating element, and thermostats with a multimeter, including live-voltage tests — are deliberately not here: neither maker's homeowner guidance prints them, and the makers route a no-heat dryer that passes these checks to service instead.
First: is it heating at all?
Both makers start by separating "no heat" from "not enough heat," because the two problems have different fixes. Their tests differ slightly, and both are printed here with their makers' names:
- Whirlpool's test: select a heated timed cycle, run the cycle for 5 minutes with the dryer empty, then open the door and feel inside.
- Samsung's test: set the dryer to Time Dry, make sure Eco Dry is turned off, start the cycle, and after 30 seconds open the door and feel inside. If there is any heat or warmth at all, Samsung sends you to its "not hot enough" path instead — service is almost never required for a dryer that heats somewhat. Samsung also says to check for an error code first: a code may mean the dryer needs service and no other troubleshooting needs to be performed.
If the drum is stone cold on a cycle that is supposed to heat, keep going down this page.
The cycles that add no heat on purpose
- Air Only / Air Fluff. Whirlpool: the Air Only cycle or Air/Fluff Only does not add heat to the dryer at any time during the cycle — it is made for items where no heat is desired, such as items that shrink easily. A load run on Air Only comes out cold because the dryer was told to keep it cold.
- Eco Dry. Samsung: Eco Dry intentionally reduces heat output to save energy, and the beginning of the cycle does not use any hot air at all. On models with the setting, Eco Dry can turn itself on automatically for common cycles like Normal or Time Dry — you may be using it without realizing it, and Samsung says turning it off for the test is part of the test.
Electric dryers: the two-breaker rule
This is the check the makers put first for electric dryers, and it explains the exact symptom — a dryer that runs but won't heat:
- Whirlpool: electric dryers require a separate 30-amp circuit fused on both sides of the line, which means there are 2 circuit breakers operating the dryer. One circuit operates the motor, turning the drum; the other operates the heating element. If one of them is tripped, the dryer may not heat. Check that both breakers are not tripped.
- Samsung: electric dryers have two circuits; in most homes they are connected so they trip together, but it is possible for only one circuit to trip — and if that happens, the dryer will turn on and spin but will not heat. Samsung's action: turn the circuit breaker off, wait 30 seconds, and turn it back on, which confirms both circuits are on.
- The supply itself. Whirlpool: electric dryers require a 240-volt power supply, and without 240 volts the dryer will not operate correctly — check with a qualified electrician. Samsung's installation review says the same from the outlet side: if the outlet is not supplying enough voltage, the panel and motor may work, but the heater may not. Power-cord installation questions belong to an electrician on both pages; Whirlpool's one homeowner note is to unplug the dryer before checking that the terminal screws are tight.
Gas dryers: the shutoff valve
Whirlpool's gas page is short and pointed: make sure the dryer is connected to the gas supply, because the drum of a gas dryer will turn, but the dryer will not heat, if the gas shutoff valve is closed. Open the gas shutoff valve in the supply line — the valve is open when the handle is parallel to the gas pipe. Whirlpool also has you check the household side: make sure a household fuse has not blown or a circuit breaker has not tripped, and reset or replace as necessary. Samsung's installation review for gas dryers is one line: verify the gas line connection is installed properly and turned on. That is the whole of the makers' gas guidance for homeowners — everything past the valve (igniters, gas valve coils, flame sensors) is service work, and neither maker prints homeowner steps for it.
The vent still matters
Samsung's guide gives the vent a real role in a no-heat complaint: the dryer may not heat if it detects that heat and moisture are not leaving, which it does to prevent overheating and fires in the vent. Samsung models with a vent blockage test run it from the control panel (the button combinations vary by model and are in the guide and your manual); a result like CLg, Cg, C80, or C90 means a clog was detected. Whether or not your dryer can test itself, Samsung's vent rules are the same: clean the exhaust vent once or twice a year whether you have issues or not; the vent must be correctly fitted and sealed, of the proper material and not plastic or foil, not longer than its maximum length (every 90-degree turn reduces the maximum by 6 feet), and free of kinks or flattening. Whirlpool's long-dry-times guide agrees that poor ventilation is a leading cause of drying trouble, with its own homeowner line — unplug the dryer before inspecting the vent.
Where the makers stop
Samsung states the dividing line plainly: dryer heater failure usually means no heat at all. So if the vent blockage test passes and your dryer is still not heating at all, Samsung's step is to request service. Whirlpool's pages end the same way — still not heating after the cycle, breaker, and valve checks means contacting the maker or scheduling service. The parts the repair sites test with meters — thermal fuse, heating element, cycling thermostat, igniter — are exactly the parts neither maker puts in front of homeowners, and a blown thermal fuse in particular is a safety device that did its job, not a reset button. If your dryer shows an error code, both makers say to start there instead: Samsung's code guide may send you straight to service, and clearing a code does not repair its cause.
The bottom line: Confirm the no-heat is real with a heated timed cycle, rule out the cycles that add no heat on purpose (Air Only; Eco Dry), then check the supply your dryer actually uses: both breakers on an electric dryer — one tripped breaker is the classic runs-but-won't-heat fault — or the shutoff valve, handle parallel to the pipe, on a gas dryer. Run Samsung's vent checks if your model offers them. A dryer still making no heat at all after that has, in the makers' shared judgment, a failed heater or another internal fault — and that is a service call, not a parts hunt.
General information only — not a substitute for your dryer's own manual or a qualified appliance technician's judgment about your dryer.
Sources
Whirlpool Product Help, "Not Heating - Electric Dryer" (producthelp.whirlpool.com): to test if the dryer is heating, select a heated timed cycle, run the cycle for 5 minutes (empty dryer), and open the door and feel inside; the Air Only cycle or Air/Fluff Only does not add heat to the dryer at any time during the cycle, and air only cycles are best used for items where no heat is desired, such as items that will shrink easily; electric dryers require a separate 30-amp circuit fused on both sides of the line, which means there will be 2 circuit breakers to operate the dryer — one circuit will operate the motor (turning the dryer drum) while the other circuit will operate the heating element — and if one of these is tripped, the dryer may not heat, so check that both circuit breakers operating the dryer are not tripped; electric dryers require a 240-volt power supply, and if you do not have 240-volt, your electric dryer will not operate correctly — check with a qualified electrician, ensure the power cord is properly installed per the installation instructions, and unplug the dryer before checking the terminal screws. Read in full November 8, 2026. https://producthelp.whirlpool.com/@api/deki/pages/20178/pdf/Not%2bHeating%2b-%2bElectric%2bDryer.pdf
Whirlpool Product Help, "Not Heating - Gas Dryer" (producthelp.whirlpool.com): to test if the dryer is heating, select a heated timed cycle, run the cycle for 5 minutes (empty dryer), and open the door and feel inside; the Air Only cycle or Air/Fluff Only does not add heat to the dryer at any time during the cycle; make sure the dryer is connected to the gas supply — the drum of a gas dryer will turn, but the dryer will not heat if the gas shutoff valve is closed — and open the gas shutoff valve in the supply line, the valve being open when the handle is parallel to the gas pipe; and check to make sure a household fuse has not blown or that a circuit breaker has tripped, and reset the circuit breaker or replace the fuse if necessary. Read in full November 8, 2026. https://producthelp.whirlpool.com/@api/deki/pages/20307/pdf/Not%2bHeating%2b-%2bGas%2bDryer.pdf
Samsung Support (US), "Clothes are not dry after using Samsung dryer" (samsung.com/us/support/troubleshooting/TSG01000999/): if a dryer is heating but the clothes are still damp, the vent is probably blocked, and weak heat with long run times can also indicate a blocked vent; first check whether an error code is displaying, because an error code may mean the dryer needs service and no other troubleshooting needs to be performed; some settings, like Eco Dry, cause portions of the cycle (like the beginning) to operate without heat; to test for heat, set the dryer to Time Dry, make sure Eco Dry is turned off, and after 30 seconds open the door and feel inside — if there is any heat or warmth, use the "not hot enough" steps instead, and only continue the no-heat steps if the dryer does not heat at all; electric dryers require 240V outlets, and if the outlet is not supplying enough voltage, the panel and motor may work but the heater may not; for gas dryers, verify the gas line connection is installed properly and turned on; electric dryers have two circuits which in most homes are connected so they trip together, but it is possible for only one circuit to trip, and if this happens the dryer will turn on and spin but will not heat — turn the circuit breaker off, wait 30 seconds, and turn it back on to confirm both circuits are turned on; the dryer may not heat if it detects that heat and moisture are not leaving (to prevent overheating and fires in the vent); the built-in vent blockage test (button combinations vary by model) reports 0 or End for a clear duct and CLg, Cg, C80, or C90 for a detected clog; clean the exhaust vent once or twice each year whether you experience issues or not; the vent must be correctly fitted and sealed without gaps, of the proper material and not plastic or foil, not longer than the maximum length in the user manual (every 90-degree turn reduces the maximum length by 6 feet), and free from kinks or flattening; Eco Dry intentionally reduces heat output to save energy, does not use any hot air at the beginning of the cycle, and on models with the setting will automatically turn on for certain common cycles like Normal or Time Dry; dryer heater failure usually means no heat at all; and if the vent blockage test passes but the dryer is not heating at all, request service. Read in full November 8, 2026. https://www.samsung.com/us/support/troubleshooting/TSG01000999/
Also read in full: Whirlpool Product Help, "Dryer is not Drying or Experiencing Long Dry Times" — its heat test repeats the heated-cycle, 5-minute, feel-inside procedure; it states that poor ventilation is a leading cause of long dry times and to unplug the dryer before inspection; and it directs readers to arrange service if the dryer does not heat. Read in full November 8, 2026.
Checked November 8, 2026.
Related guides: Oven Not Heating, Dishwasher Not Draining, Dryer Takes Too Long to Dry, Garbage Disposal Humming but Not Spinning and Refrigerator Not Cooling.