Answered Plainly
Display: Text size:

Leer esta guía en español

Dishwasher Not Draining — The Water in the Bottom, Explained

Short answer: Whirlpool's own Product Help page puts a non-draining dishwasher down to the drain path: water leaves through the filter and the sump, gets pushed by a drain pump, and exits through a hose that must rise in a loop before it falls to the sink drain or the garbage disposal. A blockage at any of those points leaves water standing in the tub. Whirlpool's walk checks them in a safe order — power off at the breaker first, bail the water out, clean the filter, look in the sump, run the kitchen tap, and read the water level like a gauge. Two endings are not blockages at all: a drain that makes no sound, or one that only hums, means the motor — and Whirlpool says a service technician is needed for both.

General information only — not a substitute for your dishwasher's own manual or a qualified appliance technician's judgment about your dishwasher. This page follows Whirlpool's published troubleshooting for its own dishwashers. The steps stay on the owner side of the machine — filter, sump, hoses as installed. Nothing here takes the dishwasher apart, and Whirlpool's own safety order is kept: the breaker comes before your hands.

Before your hands go in: Whirlpool's three preparations

And one standing rule from the same page, before anything is poured anywhere: do not use professional drain opening chemicals in a dishwasher. The drain path on this page is cleared by hand and by water, never by chemicals.

Step 1: the filter — the most common parking spot for the problem

Every load's water passes through the filter at the bottom of the tub, and Whirlpool routes you there first. Remove it the way the page describes: any separate UltraFine or cup filter lifts straight out; the cylindrical filter unscrews — push it down and rotate a quarter turn counterclockwise, then lift it out. Clean it following your Use and Care Guide. A filter matted with food residue is a drain restriction all by itself, and this is the step most likely to be the whole story.

While you are there, Whirlpool adds a related flush: run water at the nearest sink until it is hot, then run a cycle — warm water through the machine helps clear soft buildup from the spray arms and the path the water takes. It costs nothing and it is the maker's own suggestion.

Step 2: the sump — check for the hard little things

Under and around the filter sits the sump, the low basin the pump draws from. Whirlpool's instruction: check the sump area (inside the dishwasher) for any large food particles, glass, bones, or foreign objects that could be in the way. Glass gets its own mention twice on the maker's pages — a shard or a bone that escaped a plate can block or jam what a gallon of rinse water cannot. Look and feel carefully; this is exactly why the breaker step came first.

Step 3: read the water level like a gauge

Whirlpool gives the standing water itself a diagnostic meaning, and it is the most useful sentence on the page:

So the depth of the puddle separates the two families of causes: shallow means the path is narrowed somewhere; deep means the path is shut, or the push itself is gone.

Step 4: the hose's high loop, the air gap, and the famous plug

The drain hose's shape matters. Whirlpool: for proper draining, the dishwasher hose should come up and loop — in what is called a high loop — or connect to an air gap if your local plumbing code requires one; and if your sink has an air gap (the small chrome cap beside the faucet), make sure it is not clogged. On the maker's list of ways water ends up standing in the tub: a bent or kinked drain hose, a hose that was never properly connected, and — the classic — a food disposer plug that was never removed.

That last one deserves its own sentence, because it explains the dishwasher that has never drained since the day the new garbage disposal went in. Whirlpool: if a new garbage disposal was recently installed, the knockout plug inside it must be removed for the dishwasher to drain properly. The plug is there to keep the port sealed until a dishwasher is hooked to it; leave it in, and the dishwasher is pumping against a wall.

Step 5: listen while it tries to drain — the two sounds that end the page

If the path looks clear and the water still stands, Whirlpool's final check is your ears. Start a drain and listen:

Whirlpool's verdict on both is identical, and this page prints it without dressing it up: in both situations, a service technician is needed to diagnose and repair the issue. The pump and motor live past the owner-service line; reaching them is not a filter-and-towels job.

Stop lines.

Breaker first, always. Hands go into a machine full of water and sharp debris only with the fuse or breaker off — never on the panel button's say-so. That is Whirlpool's wording, and it is the whole ballgame.

No drain chemicals. Whirlpool says so outright. A dishwasher's drain path is cleared by removing the blockage, not by dissolving it.

Silence or humming from the drain motor means stop. Both are technician diagnoses on the maker's own page. Bailing the water out so nothing stagnates is the useful thing a homeowner can still do.

How this page differs from a parts list

Repair blogs tend to answer this symptom with a shopping list — new pump, new check valve, new hose. Whirlpool's own page is more disciplined, and this page has kept its shape: power off, water out, filter, sump, hose shape, plug, then ears. Most standing-water dishwashers are cured somewhere in the first three of those. The rest were never blockages — they were motors — and the maker says who those belong to.

General information only — not a substitute for your dishwasher's own manual or a qualified appliance technician's judgment about your dishwasher. Model-specific filter shapes and hose routings vary; your Use and Care Guide is the authority for your machine. The source below is the whole basis of this page, and it is worth reading in the original.

Sources

Whirlpool Product Help, "Dishwasher Not Draining" (producthelp.whirlpool.com, page updated November 8, 2026): possible causes include the pump and motor assembly, and checking the drain pump impeller for glass, debris, or damage. Preparation: eliminate any excessive water remaining in the bottom of the dishwasher tub, by bailing it out (excessive water can be caused by a drain restriction or a failure of the drain pump); for safety purposes, electricity should always be turned off for the appliance — switch off the fuse or circuit breaker — and do not rely on pressing the power on/off function on the control panel for any of these steps; place towels under the dishwasher or on the floor to protect from water during the filter removal process. Filter: remove any UltraFine or cup filter (pull straight up to remove); remove the cylindrical filter by pushing down and rotating a quarter turn counterclockwise, then lift it out; clean the filter per the Use and Care Guide. Also: run water at the nearest faucet until it is hot, then run a cycle — this will clean the spray arms of hard water and sediment. Sump: check the sump area (inside the dishwasher) for any large food particles, glass, bones, or foreign objects. Air gap: if the sink has an air gap fitting, make sure it is not clogged. Water level: water in the bottom of the tub sitting just slightly above the filter indicates a partial drain restriction; a full bottom of tub water extending near the door indicates a severe drain blockage or a potential failed drain pump motor. Drain hose: for proper draining the dishwasher hose should come up and loop (high loop) or connect to an air gap if required by local plumbing code; standing water also results from the drain hose not being installed correctly — a bent or kinked drain hose, a disposer plug that has not been removed, or the drain hose not properly connected. New disposal: if a garbage disposal was recently installed, ensure that the knockout plug has been removed — essential for proper drainage. Listen test: when starting the drain — no sounds may indicate an issue with the drain motor; a humming sound may indicate the motor impeller is jammed; in both situations a service technician is needed to diagnose and repair the issue. And: do not use professional drain opening chemicals. Read in full November 8, 2026.

Checked November 8, 2026.

Related guides: Garbage Disposal Humming but Not Spinning, Oven Not Heating, Refrigerator Not Cooling, Dryer Not Heating and Old Equipment.