Washing Machine Won't Drain in Plain Words
General information only — not a substitute for your washer's own manual or a qualified appliance technician's judgment about your washer. This page follows the drain guidance Whirlpool publishes in its Product Help pages and GE Appliances publishes in its support articles. Nothing here opens the machine or tests a part: the repair sites' pump, lid-switch, and control-board tests are deliberately not on this page, because neither maker's homeowner guidance prints them. Where Whirlpool's own pages give different numbers for different models, this page prints both with the model line attached — your manual's numbers govern your machine.
Step zero: give it three minutes
GE Appliances opens its front-load drain article with a pause: if your washer is not draining, wait a few minutes, because for many models it is normal to have pauses between cycles of up to 3 minutes. If your washer has a manual dial, GE warns not to advance it by hand during a pause after agitation — you may miss the pump-out portion of the cycle. A washer that is merely pausing needs nothing.
The load, the lid, and the suds
- Door or lid not closed. Whirlpool's guide lists this first among its common reasons: the lid or door switch ensures the washer operates only when the lid is securely closed, and an unlatched door can stop draining and spinning.
- An unbalanced or tightly packed load. Both makers print this. Whirlpool: a load that is too heavy or unevenly distributed can make the washer stop spinning to avoid damage; redistribute the items or reduce the load size. Whirlpool adds that tightly packed loads may not spin correctly and leave the load wetter than usual — evenly arrange the load, then select Rinse & Spin to remove the excess water. GE says the same in one line: redistribute the clothing and/or increase the load size.
- The spin speed you selected. Whirlpool: gentle cycles — gentle, delicate, handwash — use slow spins to protect fabrics, and slow spinning leaves more water in the load. If the clothes are wet but the machine drained, a higher-spin cycle (heavy duty, for example) is the fix, always following the clothing care label.
- Too many suds. Whirlpool is specific about the mechanism: high amounts of detergent create suds that can stop the washer from pumping water and spinning. Use only HE detergent in an HE machine, always measure, and use less if your water is very soft; non-HE detergent or more than the recommended amount causes excessive suds, and the excess suds make the washer run at a reduced spin speed, leaving very wet loads. Whirlpool's manual troubleshooting chart gives the recovery: to remove extra suds, select Rinse & Spin and do not add detergent.
The drain hose: the numbers both makers print
This is where the makers get exact, and where most real faults live.
- Not kinked, not clogged. Both makers: make sure the drain hose is not kinked or clogged; straighten it for adequate water flow, and remove any blockage from the drain hose, the drainpipe, or the utility sink. Whirlpool adds: use the U-shaped drain hose form and secure the hose.
- How far into the standpipe. Whirlpool's top-load page: the drain hose should not extend more than 5 inches (20.3 cm) into the standpipe or laundry tub. Whirlpool's front-load page: not more than 4.5 inches (113 mm). The reason is the same on both pages: pushed too far, drained water can siphon back into the washer. The U-shape drain hose form gives the correct length.
- How high the drain can be. Whirlpool's guide gives the standpipe window as 96 inches (244 cm) maximum and 30 inches (76.2 cm) minimum: above the maximum the washer cannot adequately pump the water out and water may flow back in; below the minimum, water flows out by gravity and the flow can create a siphon that keeps draining the machine as it fills. GE Appliances prints the matching ceiling from its side: most GE full-size washers will pump a maximum of 8 feet from the floor — the same 96 inches — and 5 feet for a compact or portable washer. One honest exception inside Whirlpool's own pages: its commercial-grade washer page prints a 39-inch (99 cm) standpipe minimum instead of 30. The minimum depends on the model line, which is why this page prints both numbers with their sources and why your installation instructions govern.
- Never tape the hose in. Both makers again. Whirlpool's front-load page: do not seal the drain hose into the drainpipe with tape; the hose should be loose yet secure, because there must be a gap between the hose and the drain pipe to let air flow through — the air gap breaks the suction and prevents water from continuously being sucked out of the machine as it fills. GE's troubleshooting page says a hose pushed too far down or taped to the standpipe can siphon water out of the washer, and points to the drain hose clip (anti-siphon clip) that came with the washer.
The pump filter (front-load models that have one)
GE explains what the filter is for: small items from clothing or pockets can pass to the drain pump, and the washer has a filter to capture them so they are not dumped into the plumbing — but captured items can clog the filter and slow or prevent draining. If your model has an access door to the pump filter at the front of the washer, GE says the pump filter should be cleaned, and tells you to use your owner's manual to determine whether your model has a filter you can clean yourself. Whirlpool's front-load page says the same in fewer words: the drain pump filter may be clogged with dirt, lint, or other items, and should be cleaned on an occasional basis to keep the washer operating properly. Neither maker's page prints a universal procedure — location and steps vary by model — so the manual is the procedure. GE's boundary is worth knowing: models without front access require service for this.
Check the house drain itself
Sometimes the washer is fine and the house drain is not. GE prints the test: the drain hose goes into a standpipe, drain, or other household plumbing — remove the drain hose and pour a quart of water into the standpipe or drain. If the water will not drain, GE's recommendation is a plumber. Its troubleshooting page puts the same point in its own line: ensure the drain in your household plumbing is not clogged, and household plumbing issues will require a plumber to resolve.
The sound that is not water in the tub
One reassurance both makers print, because it sends people shopping for a fault that isn't there: if you hear water sloshing but see no water in the tub, that is the balance ring. Whirlpool describes it as a fluid-filled ring at the top of the tub whose fluid shifts opposite the load to keep the basket stable and allow higher spin speeds — and you may also hear it after moving the washer. GE's version: an enclosed plastic container partially filled with a saltwater (brine) solution, attached to the inner clothes basket. Hearing it is normal.
Where the makers stop
GE prints the clearest stop line in either maker's pages: if the tub is full of water and the washer just hums, you will need to schedule service. Beyond that, internal causes — a failed pump, a lid or door switch, a control — are diagnosis a technician does with the machine open and a meter in hand. Neither maker's homeowner pages print those tests, so this page doesn't either: if the checks above leave water standing, the makers' shared answer is service (Whirlpool: contact us or schedule service; GE: schedule a repair appointment).
The bottom line: Wait out the normal 3-minute pause first. Then, in the makers' order: door or lid fully closed, load balanced and not packed tight, a cycle with a real spin speed, detergent measured (suds alone can stop a pump-out). Then the hose: unkinked, no more than about 4.5–5 inches into the standpipe depending on the model, the standpipe between its minimum and the 96-inch maximum, and never taped. Then the pump filter if your model gives you access to one, and the quart-of-water test for the house drain. Standing water plus a hum is the makers' service line.
General information only — not a substitute for your washer's own manual or a qualified appliance technician's judgment about your washer.
Sources
Whirlpool Product Help, "Not Draining - Washer" (top load) (producthelp.whirlpool.com): the drain hose should not extend more than 5" (20.3 cm) into the standpipe (drainpipe) or laundry tub (typically up), and using the U-shape drain hose form as described in the Installation Instructions provides the correct drain hose length; the drain hose cannot extend higher than 96" from the floor; do not tape the drain hose to the drain pipe; make sure the drain hose is not kinked or clogged, straighten the hose for adequate water flow, and remove any blockage from the drainpipe or utility sink; use only HE High-Efficiency detergent and always measure detergent — if you have very soft water you may need less — because using non-HE detergent or more than the manufacturer's recommended amount can cause excessive suds, and the excess suds can cause the washer to run at a reduced spin speed, resulting in very wet loads; tightly packed loads may not allow the washer to spin correctly, leaving the load wetter than usual — evenly arrange the wet load for balanced spinning and select RINSE & SPIN to remove excess water, and see the Owner's Manual for loading recommendations; water heard in the washer but not seen is normally caused by the balance ring, a fluid-filled ring at the top of the tub whose fluid shifts to the opposite side of the load to help offset the weight and keep the basket's rotation stable, allowing higher spin speeds, and you may also hear the fluid if you move your washer. Updated April 29, 2026; read in full November 8, 2026. https://producthelp.whirlpool.com/Laundry/Washers/Top_Load_Washer/Cycle_Concerns/Not_Draining_-_Washer
Whirlpool Product Help, "Not Draining - Front Load Washer" (producthelp.whirlpool.com): the Drain Pump Filter may be clogged with dirt, lint, or other items, and should be cleaned on an occasional basis to keep the washer operating properly; the drain hose may be too far down inside the drainpipe (standpipe) or laundry tub — drained water can siphon back into the washer if the drain hose extends too far — so make sure the drain hose does not extend more than 4.5" (113 mm) into the drainpipe or laundry tub, with the U-shape drain hose form providing the correct length; do not seal the drain hose into the drainpipe with tape — the drain hose should be loose, yet secure, there must be a gap between the drain hose and the drain pipe to allow air to flow through, and the air gap will break the suction and prevent water from continuously being sucked out of the machine (siphoning) as it fills; check that the top of the drain is at least 30" (76.2 cm) high as measured from the floor — if the drain is below 30" (76.2 cm), the water will start to flow out of the machine due to gravity, the flow of water can create suction (siphon), and the water will continue to drain out of the washer; if you still need help, contact us or schedule service. Updated November 7, 2026; read in full November 8, 2026. https://producthelp.whirlpool.com/@api/deki/pages/8759/pdf/Not%2bDraining%2b-%2bFront%2bLoad%2bWasher.pdf
Whirlpool Product Help, "Washer Not Draining or Spinning? Troubleshooting Guide" (producthelp.whirlpool.com): common reasons a washer won't drain or spin include the door not closed (the lid or door switch ensures the washer operates only when the lid is securely closed), an unbalanced load (an unbalanced or overloaded washer can prevent proper draining and spinning; redistribute the items in the drum or reduce the load size), the spin speed selected (gentle cycles such as gentle, delicate, or handwash use slow spins and leave more water in the load; to remove more water select a cycle that uses high spin speeds), and excessive suds (high amounts of detergent can create too many suds, and sometimes the suds can stop the washer from pumping water and spinning; always measure detergent and follow the manufacturer's directions); for the drain, check the drain hose for kinks or clogs (straighten the hose, remove any blockage from the drain hose, drainpipe, or utility sink, use the U-shaped drain hose form, and secure the drain hose), and the drainpipe height requirements are 96" (244 cm) maximum and 30" (76.2 cm) minimum — the washer will not be able to adequately pump the water out if the drainpipe exceeds 96", and in that case the water may flow back into the washer; on some front load models the Drain Pump Filter is accessible and can be cleaned, and over time it may be clogged with dirt, lint, or other items. Read in full November 8, 2026. https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Front_Load_washer_is_not_Draining%2C_not_Spinning%2C_or__Leaving_Wet_Loads
GE Appliances, "Front Load Washer - Will Not Drain or Drains Slowly" (products.geappliances.com): if your washer is not draining, wait a few minutes — for many models it is normal to have pauses between cycles of up to 3 minutes, and if you have a manual dial do not manually advance the dial/timer if it is pausing after agitation, because you may miss the pump-out portion of the cycle; make sure the drain hose is not kinked or clogged; make sure the washer is not trying to drain more than 8 feet higher than the floor — the maximum height most GE Appliances full size washers will pump is 8 feet from the floor, 5 feet for a Compact or Portable washer, with the model's Installation Instructions carrying the details; the drain hose goes into a standpipe, drain, or other household plumbing — remove the drain hose and pour a quart of water into the standpipe or drain, and if water will not drain, a plumber is recommended; small items from clothing or pockets can pass to the drain pump, and the washer's filter captures these items so they are not dumped into the plumbing or drain line, but captured items may cause a clog that can slow down or prevent draining — if your model has an access door to the pump filter in the front of the washer, the pump filter should be cleaned, and the Owner's Manual determines whether your model has a pump filter that can be cleaned manually; ensure the wash load is not out of balance — redistribute the clothing and/or increase the load size; if the tub is full of water and the washer just hums, you will need to schedule service; and if the suggestions do not help, schedule a repair appointment. Read in full November 8, 2026. https://products.geappliances.com/appliance/gea-support-search-content?contentId=23081
Also read in full: Whirlpool Product Help, "Washer Keeps Draining - Commercial Grade Washer" — the source of the 39" (99 cm) standpipe minimum and the 4.5" (113 mm) insertion figure for that model line, and of its drain-routine note (if no water is detected entering the washer after 13 minutes, the washer goes into a drain routine of approximately 8 to 10 minutes during which the control accepts no input) — and GE Appliances, "Front Load Washer - Troubleshooting" (products.geappliances.com), which repeats the kinked-hose, household-drain, and pump-filter points and adds that the drain hose should be installed using the drain hose clip (anti-siphon clip) included with the washer, and that if the hose is pushed too far down into the stand pipe or taped to it, the hose can siphon water out of the washer; models without front pump-filter access require service. Read in full November 8, 2026.
Checked November 8, 2026.
Related guides: Washing Machine Smells Bad, Lawn Mower Won't Start, Sewing Machine Skipping Stitches, Sewing Thread Bunching Underneath and Which Sandpaper Grit? Pick Your Job.