Answered Plainly
Display: Text size:

Water Heater Making Popping or Rumbling Noises — What It Means

Short answer: Popping, rumbling, or crackling from a tank water heater almost always means lime and sediment built up at the bottom of the tank. A. O. Smith, one of the biggest water heater makers, covers exactly these three sounds in its Technical Bulletin 13: the cause is lime (calcium carbonate) settling out of the water, and the popping is water trapped under the lime deposits, bursting through as it heats — or water trapped next to a heating element, boiling to steam. The maker's fix is to dissolve and flush the build-up out. It is maintenance the heater has been asking for, not a sound to learn to live with.

General information only — not a substitute for your water heater's own manual or a qualified plumber's judgment about your heater. This page follows A. O. Smith's published bulletin and the owner-manual maintenance text of another major maker, Rheem/GE.

Hot water can scald, and a water heater is a pressure vessel. The steps below are the makers' own published maintenance, in their order, with their safety lines kept in. If any step is beyond what you are set up to do — especially disconnecting water lines — a plumber can do the same work, and the diagnosis on this page will tell them exactly what you found.

Why the tank pops

Lime is present in every water system to some degree, A. O. Smith's bulletin explains, and it behaves in a way that works against you: lime is inversely soluble — the more you heat the water, the more lime comes out of it. So the hottest place in the system, the bottom of the tank where the burner or elements work, is exactly where the deposits settle and harden. Higher usage, harder water, and more heating surface all speed it up. Once a layer is down there, water gets trapped underneath it; when that trapped water boils, it pops and rumbles its way out through the layer. That is the noise. The bulletin calls treating a "limed-up" heater a necessity of modern maintenance — the layer also insulates the water from the heat, so the heater works harder to do the same job.

What each noise usually means

A. O. Smith's repair guidance separates the sounds:

So the popping family points at the tank bottom. The banging family points at a phone call.

The maker's fix — A. O. Smith's deliming steps, in order

Since lime is a base, the bulletin explains, the way to dissolve it so it can be flushed out is with an acid — food-grade phosphoric acid is the most commonly used, and standard household cider vinegar may also be used. The bulletin's published procedure:

  1. Turn the power off. Turn electricity off to the heater — or, for gas models, turn the thermostat to the pilot position. The owner manuals add their own caution in the same place: shut off power to the water heater before draining water.
  2. Turn off the cold water supply to the water heater — normally a valve on the right side, before the heater.
  3. Open a hot water faucet in a bathtub or sink to relieve the pressure in the system — and leave it on.
  4. Drain the heater completely. Connect a garden hose rated for 200°F to the drain valve at the bottom of the water heater — the rating matters, because this water is hot enough to injure and to soften an ordinary hose. Open the drain valve, let the heater drain completely, then close the drain valve.
  5. Add the vinegar. Disconnect the cold-water inlet, hot-water outlet, or the temperature-and-pressure (T&P) valve, and using a funnel, pour in one gallon of regular household cider vinegar. Do not dilute it with water.
  6. Let it sit at least six hours.
  7. Flush. Reconnect the inlet, outlet, or T&P valve. Open the drain valve and turn the water on to flush out the dissolved sediment and vinegar.
  8. Refill before reheating. Close the drain valve and fill the water heater until water comes out of the faucet you opened earlier. Close that faucet, then turn the water heater back on to reheat.

The bulletin notes it may be necessary to repeat the flushing, depending on water conditions and maintenance history — a tank that has popped for years may not come clean in one pass.

Stop lines.

Power off before draining — always. That is the manuals' caution, printed as a warning in the box because it matters: heating elements run in an empty or partly drained tank are damaged, and the work itself is electrical work around water.

The tank must be full before the heat comes back on. Step 8's order is the safeguard: water out of the open faucet first, faucet closed second, heater on last.

Banging is not a flushing problem. If the sound is a bang or hammer rather than a pop or rumble, A. O. Smith's line is professional repair — do not flush your way at a pressure problem.

Leaks, a dripping relief valve, or rust-colored water are different pages of the manual. This page is about noise from sediment. A heater that leaks, or whose relief valve weeps, needs a plumber's diagnosis, not a deliming.

Keeping the layer from coming back — two makers, two rhythms

The makers do not give one shared schedule, and this page prints both rather than merging them. The Rheem/GE owner manual treats the tank as a settling basin for solids in the water and suggests draining a few quarts of water from the tank every month to clean the tank of these deposits — small, frequent drains that keep the layer from ever hardening. A. O. Smith's bulletin is written for a tank that already has the layer: the full drain-and-delime above, repeated if the water conditions and maintenance history call for it. Either way, the direction is the same: sediment is managed on a rhythm, or it is removed in a project — it does not manage itself.

One more yearly check from the owner manual

The Rheem/GE manual's routine maintenance adds a safety check worth the minute it takes: at least once a year, lift and release the lever handle on the temperature-and-pressure relief valve — the valve near the top of the heater — to make certain it operates freely, and allow several gallons to flush through the discharge line to an open drain. That valve is the tank's last line of defense against dangerous pressure, and a valve that has seized shut from years of sitting is a hazard found cheaply, once a year, on purpose.

General information only — not a substitute for your water heater's own manual or a qualified plumber's judgment about your heater. If the noise comes with leaks, no hot water, or a relief valve that drips or will not reseat, stop and call a plumber. The sources below are the whole basis of this page, and they are worth reading in the original.

Sources

A. O. Smith, Technical Bulletin 13, "Mineral Build-Up" (hotwater.com): symptoms — rumbling, crackling, popping; cause — lime (CaCO₃) is present in every water system to some degree, is inversely soluble (the more you heat, the more lime comes out), and higher usage, excessive hardness, and increased heating surface lead to "limed-up" heaters; symptoms often include a popping of water trapped under lime deposits or the sizzling of water trapped next to elements, boiling it to steam; the fix — since CaCO₃ is a base, dissolve it with an acid so it can be flushed from the heater; the most commonly used is phosphoric acid at a food grade level, and standard household cider vinegar may also be used; the solution, in order — turn electricity off to the heater or turn the thermostat to the pilot position for gas models; turn off the cold water supply; open the hot water faucet in a bathtub or sink to relieve pressure and leave it on; connect a garden hose rated for 200°F to the drain valve at the bottom and drain the heater completely, then close the drain valve; disconnect the cold-water inlet, hot-water outlet, or T&P valve and pour in one gallon of regular household cider vinegar, not diluted; let the vinegar set for at least six hours; reconnect, open the drain valve, and turn on the water to flush out the dissolved sediment and vinegar; close the drain valve; fill the heater until water comes out of the faucet opened earlier; close that faucet and turn the water heater on to reheat; it may be necessary to repeat the flushing depending on water conditions and maintenance history. Read in full November 7, 2026.

A. O. Smith, "Water Heater Repair: Things to Consider" (hotwater.com): popping noises in a hot water tank usually mean sediment in the water heater; pressure in the system may cause a banging noise called a "water hammer," which requires professional repair; whistling noises may indicate a blocked valve; hissing usually means sediment inside the tank; sediment buildup at the bottom of the tank also causes vibrating noises. Read in full November 7, 2026.

Rheem / GE Use & Care manual, "Routine Preventative Maintenance" and "Care and Cleaning" (the maker's owner manual): a water heater's tank can act as a settling basin for solids suspended in the water, so hard water deposits commonly accumulate in the bottom of the tank; it is suggested that a few quarts of water be drained from the tank every month to clean the tank of these deposits; at least once a year, lift and release the lever handle on the temperature pressure relief valve, located near the top of the water heater, to make certain the valve operates freely, allowing several gallons to flush through the discharge line to an open drain; caution — shut off power to the water heater before draining water. Read November 7, 2026.

Checked November 7, 2026.

Related guides: What Is Hard Water?, Why Does My Tap Water Taste Metallic?, Why Does My Well Water Smell Like Rotten Eggs?, Why Is My Shower Water Yellow or Brown? and Can a Home Test Kit Really Check Lead in Your Water.